Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
   7.1. Forward suspension bracket
   7.2. Angles of installation of wheels
   7.3. Back suspension bracket
   7.4. Steering
      7.4.1. A steering wheel without safety cushion
      7.4.2. A steering wheel with a safety cushion
      7.4.3. The switch of the index of turn (the combined switch)
      7.4.4. Key of the switch of ignition and lock of blocking of a wheel
      7.4.5. Lock of blocking of a wheel
      7.4.6. Steering column
      7.4.7. Steering drafts
      7.4.8. Steering mechanism
      7.4.9. The steering mechanism with the hydraulic booster
      7.4.10. Pump of the hydraulic booster
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Suspension bracket and steering>> Steering>> Steering drafts

7.4.7. Steering drafts

SIDE DRAFTS

Removal and installation

PERFORMANCE ORDER
1. Lift the car and remove forward wheels.
2. Rasshplintuyte a koronchaty nut of a tip of draft, turn off a nut. Vypressuyte a tip from a pin eye also disconnect draft.
3. Apply a tag on a carving part of draft (paint or wind with a tape). Turn off a lock-nut and turn out draft from a steering rack.
4. Wrap draft to the tag put when dismantling. Tighten a lock-nut with m 34 N.' moment.
5. Insert draft into a pin eye. Tighten a tip nut with m 39 N.' moment, tighten a nut to insert the forelock. Replace the forelock.
6. Establish forward wheels and lower the car.
7. Check and adjust the angles of installation of wheels.

INTERNAL DRAFT (THE GEAR LATH ASSEMBLED WITH THE STEERING MECHANISM)

Removal

PERFORMANCE ORDER
1. Remove a gear lath assembled with the steering mechanism (see subsection 7.4.8).
2. Turn out side draft and remove a dustproof cover.
3. Clamp a lath in a vice with soft sponges.
4. Straighten a lock washer blows of the hammer to a chisel.
5. Turn out internal draft.

Installation

PERFORMANCE ORDER
1. Wrap internal draft with m 88 N.' moment, establish a new lock washer.
2. Tire out a lock washer with the hammer and a chisel.
3. Put on a dustproof cover and establish side draft with a tip.
4. Establish a gear lath assembled with the steering mechanism (see subsection 7.4.8).

AVERAGE DRAFT AND LATH OF THE MECHANISM WITH THE WORM STEERING REDUCER

Removal

PERFORMANCE ORDER
1. Lift the car and establish on supports.
2. Rasshplintuyte spherical tips of intermediate draft in the place of a joint with a bipod of a wheel and the shock-absorber. Turn off koronchaty nuts. Vypressuyte tips from eyes of average draft.
3. Turn off a nut and remove a kontryashchy washer from tips of average draft, a vypressuyta a tip of average draft from the pendular lever.
4. Remove average and side drafts.
5. If average draft changes, then remove side drafts.

Installation

PERFORMANCE ORDER
1. Clear a carving of tips of drafts. Check a condition of a carving on which there should not be broken threads.
2. Install average draft on the pendular lever and tighten a nut with m 65 N.' moment.
3. Raise draft and establish on a bipod, tighten a tip nut with m 55 N.' moment. Tighten a nut and install the new forelock.
4. Connect draft to the shock-absorber, tighten a nut with m 105 N.' moment. Tighten a nut and install the new forelock.
5. Establish side drafts in tips of average draft and tighten nuts with m 55 N.' moment. Tighten nuts and install new forelocks. Grease the carving terminations of tips of drafts.