Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
   7.1. Forward suspension bracket
      7.1.1. Torsion
      7.1.2. Shock-absorbers of a forward suspension bracket
      7.1.3. Top spherical support
      7.1.4. Lower spherical support
      7.1.5. Stabilizer
      7.1.6. Bars of racks
      7.1.7. Top levers of a suspension bracket
      7.1.8. Lower levers of a suspension bracket
      7.1.9. Pin
      7.1.10. Naves of forward wheels
   7.2. Angles of installation of wheels
   7.3. Back suspension bracket
   7.4. Steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Suspension bracket and steering>> Forward suspension bracket>> Pin

7.1.9. Pin

GENERAL INFORMATION

Pin and details of a suspension bracket (the Amigo/MU/Jazz cars with a formula 4х2)

1 – nut and forelock
2 – nut and forelock
3 – nut and forelock
4 – tip of steering draft
5 – pin
6 – top spherical hinge
7 – bolt and plate
8 – lever axis nuts
9 – top lever assembled
10 – nut and washer
11 – plug
12 – lever axis
13 – lower spherical hinge
14 – nut, washer and bolt
15 – lower lever
16 – plug

Pin and details of a suspension bracket (the Amigo/MU/Jazz, Rodeo/Passport and Trooper/Bighorn cars with a formula 4х4)

1 – nave and board of a brake
2 – nut and forelock
3 – nut and forelock
4 – pin
5 * – an epiploon
6 * – a washer
7 * – the needle bearing
8 – top spherical hinge
9 – bolt and plate
10 – lever axis nuts
11 – plates for adjustment of longitudinal
turn axis inclination
12 – plates for adjustment of disorder of wheels
13 – top lever
14 – nut
15 – washer
16 – plug
17 – lever axis
18 – lower lever
19 – nut and washer
20 – bolt
21 – nut and washer
22 – bolt
23 – gentle lever
24 – torsion lever arm
25 – plugs
26 – plugs
* except the Amigo/MU/Jazz car with a formula 4х2

CARS WITH the FORMULA 4х2

Removal

PERFORMANCE ORDER
1. Lift the car and establish on supports. Remove wheels.
2. Establish a jack under the lower levers and raise the car to unload springs.
3. Get forelocks from nuts of hinges of the top and lower levers and turn off nuts so that the end face of a nut appeared aflush with an end face of a carving part of the hinge.
4. By means of a stripper to a vypressuyta a tip of steering draft from a pin eye.
5. Remove a support of a brake and bind a wire (see subsection 8.10).
6. Remove a board of a brake and a disk (see subsection 8.11).
7. Disconnect the top and lower spherical hinges.
8. Remove a pin, without having damaged covers of spherical hinges.

Installation

PERFORMANCE ORDER
1. Establish a pin.
2. Attach the top and lower spherical hinges to a pin. Tighten nuts of hinges with m 14 N.' moment.
3. Establish a board of a brake and a disk (see subsection 8.11).
4. Establish a brake support (see subsection 8.10).
5. Establish tips of steering drafts in pin eyes, tighten nuts of tips with 16 N.' moment of m of Zakontrite of a nut new forelocks.
6. Establish wheels and lift the car.
7. Adjust the angles of installation of wheels (it is carried out in service of car service).

CARS WITH the FORMULA 4х4

Removal

PERFORMANCE ORDER
1. Lift the car and establish on supports. Remove forward wheels.
2. Remove a brake support, a board of a brake and a disk.
3. Establish a jack under the lower lever and raise the car to unload springs.
4. Get forelocks from nuts of hinges of the top and lower levers and turn off nuts so that the end face of a nut appeared aflush with an end face of a carving part of the hinge.
5. By means of a stripper to a vypressuyta a tip of steering draft from a pin eye.
6. Disconnect the top and lower spherical hinges.
7. Remove a pin, without having damaged covers of spherical hinges.

Installation

PERFORMANCE ORDER
1. Establish a pin.
2. Attach the top and lower spherical hinges to a pin. Tighten nuts of hinges with 14 N.' moment of m of Zakontrite of a nut new forelocks.
3. Establish a disk and a board of a brake (see subsection 8.11).
4. Establish a brake support (see subsection 8.10).
5. Establish tips of steering drafts in pin eyes, tighten nuts of tips with 16 N.' moment of m of Zakontrite of a nut new forelocks.
6. Establish wheels and lift the car.
7. Adjust the angles of installation of wheels (it is carried out in service of car service).