Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
   6.1. Manual transmission
   6.2. Automatic transmission
   6.3. Running gear
      6.3.1. Forward driveshaft, half shafts and CV JOINTS
      6.3.2. Internal CV JOINT
      6.3.3. Removal and installation of the forward driveshaft
      6.3.4. Dismantling of cardan hinges
      6.3.5. Back driveshaft
      6.3.6. Average support
      6.3.7. Zadny Bridge
      6.3.8. Forward leading bridge
         6.3.8.1. Details of the forward leading bridge
         6.3.8.2. Reducer epiploon
         6.3.8.3. A nave with manual blocking of the drive of a forward driving wheel
         6.3.8.4. Self-locking nave
         6.3.8.5. Reducer of the forward bridge
         6.3.8.6. Removal and installation of the forward bridge
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Transmission and running gear>> Running gear>> Forward leading bridge>> Self-locking nave

6.3.8.4. Self-locking nave

GENERAL INFORMATION

Details самоблокируещейся naves (cars with a wheel formula 4х4)

1 – bolt
2 – nave cap
3 – case and details
4 – stoprony ring and package of washers
5 – coupling
6 – lead
7 – контрящаяся washer

8 – nut
9 – nave and disk
10 – the external bearing with a holder
11 – epiploon
12 – the internal bearing with a holder
13 – bolt
14 – wheel hairpin

Dismantling

PERFORMANCE ORDER
1. Transfer a control lever the transfer case to situation 2H. Roll the car forward and back approximately on 1 m.
2. Turn off bolts and take off a nave cap.
3. Release nuts of wheels.
4. Lift the car and establish on supports.
5. Turn off bolts of fastening of a support of a brake to a rack of a pin and fix a support by a wire. Not to disconnect hoses of brakes.
6. Get a lock ring and remove a package of washers.
7. Remove the coupling, a lead and a kontryashchy washer.
8. Weaken a nave nut inhaling.
9. Remove a nave from a pin.
10. If necessary press bearings easy blows to a brass mandrel.
11. If the brake disk is removed, then put tags of mutual orientation of a disk and a nave then turn off bolts and remove a disk.

Assembly

PERFORMANCE ORDER
1. Assembly is carried out in the return sequence.
2. Adjust an inhaling of a nut of a forward wheel in the following order:
2.1. Tighten a nave nut with m 27 N.' moment.
2.2. On return a bolt on a hairpin of a wheel and establish a dynamometer.
2.3. Improve a nut before creation of a tightness in bearings approximately in 18–22 N if new bearings and an epiploon, and 8–16 N are installed if bearings and an epiploon did not change.
3. Adjust an axial side play of a nave in the following order:
3.1. Establish on a nave a special mandrel against the stop in a kontryashchy washer.
3.2. Measure by the probe a gap between a nave and a flute of a lock ring on a half shaft.
3.3. If the gap exceeds flute width for a lock ring, then pick up a package of washers of such thickness that the gap was within 0–0,1 mm.
4. Grease nave cap bolts with the structure fixing from an otvorachivaniye and tighten bolts with m 60 N.' moment.