Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. Electric equipment and capital repairs of engines
   3.3. Diesel engine 2,8 liters
      3.3.1. Introduction
      3.3.2. Technical characteristics
      3.3.3. Check of a compression
      3.3.4. Top dead point of the piston No. 1 (BMT)
      3.3.5. Gaps of valves
      3.3.6. Cover of a head of cylinders
      3.3.7. Pulley of a bent shaft
      3.3.8. Casings of a gear belt of the drive of the camshaft
      3.3.9. Gear belt of the drive of the camshaft
      3.3.10. Asterisks of a gear belt, natyazhitel and intermediate pulleys
      3.3.11. Yokes and pushers
      3.3.12. Head of the block of cylinders
      3.3.13. Oil case
      3.3.14. Oil pump
      3.3.15. Oil heater
      3.3.16. Epiploons of the camshaft and bent shaft
      3.3.17. Flywheel
      3.3.18. Fastenings of the engine / transmission
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Engines>> Diesel engine 2,8 liters>> Cover of a head of cylinders

3.3.6. Cover of a head of cylinders

Removal

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Weaken a lock clip and pick up the phone connecting the throttle valve of system of bystry heating of the engine to a metal tube of an intermediate cooler.
3. Disconnect vacuum hoses from the throttle valve, having taken their correct arrangement into account.
4. Weaken the clip fixing a tube of the throttle valve to a collector.
5. Unscrew fixing bolts and disconnect the throttle valve from an inlet collector.
6. Disconnect a ventilating hose from a cover of a head of cylinders.
7. Unscrew the fixing bolts and nuts fixing a tube of control of exhaust gases to collectors and pick up the phone.
8. Remove laying from both ends of a tube and throw out them; when carrying out installation will be necessary new.
9. Uncover a maslozalivny mouth, unscrew fixing bolts and remove the isolating laying from a cover of a head of cylinders.
10. Weaken and remove fixing nuts together with washers.
11. Uncover a head of cylinders and laying of a cover.
12. Examine laying and washers; if on them there are traces of damages or wear, then these details need to be replaced.

Installation

PERFORMANCE ORDER
1. Before establishing, examine an internal surface of a cover of a head of cylinders on existence of deposits from oil rainfall or any other pollution.
2. If necessary clean a cover paraffin or water-soluble solvent.
3. Dry a cover before establishing it into place.
4. Make sure that a cover dry and pure and establish on it laying.
5. Establish a cover on a head of cylinders.
6. Check whether laying was displaced.
7. Put on sealing washers and lock-nuts.
8. Tighten nuts till the required inhaling moment.
9. Establish the isolating laying and tighten fixing bolts.
10. Connect a ventilating hose.
11. Check that the joined surfaces of a tube of control of exhaust gases were pure and dry.
12. Put on new laying the ends of a tube, establish a tube into place and tighten bolts and nuts of its fastenings.
13. Install the throttle valve of system of bystry heating of the engine and tighten its fixing bolts.
14. Check that vacuum hoses were connected correctly.
15. Connect a wire of the minus plug of the accumulator.