Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. Electric equipment and capital repairs of engines
   3.3. Diesel engine 2,8 liters
      3.3.1. Introduction
      3.3.2. Technical characteristics
      3.3.3. Check of a compression
      3.3.4. Top dead point of the piston No. 1 (BMT)
      3.3.5. Gaps of valves
      3.3.6. Cover of a head of cylinders
      3.3.7. Pulley of a bent shaft
      3.3.8. Casings of a gear belt of the drive of the camshaft
      3.3.9. Gear belt of the drive of the camshaft
      3.3.10. Asterisks of a gear belt, natyazhitel and intermediate pulleys
      3.3.11. Yokes and pushers
      3.3.12. Head of the block of cylinders
      3.3.13. Oil case
      3.3.14. Oil pump
      3.3.15. Oil heater
      3.3.16. Epiploons of the camshaft and bent shaft
      3.3.17. Flywheel
      3.3.18. Fastenings of the engine / transmission
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Engines>> Diesel engine 2,8 liters>> Oil case

3.3.13. Oil case

GENERAL INFORMATION

Prevention

During assembly new fixing bolts of the lower and top sections of an oil case will be necessary for you.


Removal

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Put the car on the emergency brake, lift a jack a forward part and fix it on the racks substituted under axes.
3. Turn off fixing bolts and remove a protective guard of the engine.
4. Merge engine oil, establish new sealing laying and screw up a cap of a drain opening. If the term of replacement of oil and an oil filter comes nearer, it is recommended to replace the filter on new, and upon termination of works to fill the engine with new engine oil.
5. Unscrew a forward axis from longerons and slowly lower it that the gap sufficient for removal of an oil case was formed.

Prevention

It is not obligatory to carry out this procedure if you are going to remove only the lower section of an oil case.


6. Weaken and unscrew the bolts fixing the lower section of an oil case to top.
7. Uncouple connection, having struck the lower part of a case with a hand palm.
8. Disconnect the lower part of an oil case from the engine, trying not to damage a maslopriyemny branch pipe and the mesh filter of the oil pump.
9. Remove laying and throw out it.
10. Get the probe for measurement of level of oil from a tube.
11. Unscrew fixing bolts of a tube and get a tube from the top part of an oil case. During installation of a tube use new sealing rings.
12. Twist the nuts fixing a returnable oil hose of a turbocharger to the main part of an oil case and remove a hose.
13. Remove laying and throw out it; in installation time it is necessary to use new.
14. Weaken a fixing clip and disconnect a returnable oil hose of the vacuum pump from an oil case.
15. Weaken and unscrew the bolts fixing the transmission block to a back part of an oil case.
16. Screw in and get the bolts fixing the main part of an oil case to the block of cylinders.
17. Uncouple connection, having struck the lower part of a case with a hand palm.
18. Disconnect the main part of an oil case from the engine, trying not to damage a maslopriyemny branch pipe and the mesh filter of the oil pump.
19. Check a condition of sealing laying of covers of forward and back radical bearings.
20. If necessary, replace them.
21. Check also maslopriyemny branch pipe and the mesh filter for existence of damages and replace it if necessary.

Installation

PERFORMANCE ORDER
1. Remove all traces of dirt and oil from the joined surfaces of an oil case and the block of cylinders.
2. Apply the pressurizing structure on the joined surfaces of an oil case. Try to apply sealant so that it did not get to openings of bolts.
3. Check that sealing laying of covers of forward and back radical bearings was established correctly.
4. Put the top part of an oil case to the block of cylinders, insert fixing bolts and tighten them a hand.
5. Tighten all bolts in turn till the necessary moment of an inhaling (tighten bolts in the diagonal sequence).
6. Insert the bolts fixing a transmission casing to an oil case and tighten them.
7. Establish new laying on a turbocharger oil return tube. Connect a tube to an oil case and tighten lock-nuts.
8. Connect a hose of return of oil of the vacuum pump to an oil case and fix a hose by means of a lock clip.
9. Establish new sealing rings on a maslopriyemny branch pipe and oil them engine. Insert a branch pipe on the place and tighten fixing bolts.
10. Check that the joined surfaces of the lower part of an oil case were pure and dry, and apply on them a sealant layer. You apply sealant so that it did not get to openings of bolts.
11. Establish new laying on an oil pan and put it to an oil case. Insert fixing bolts and tighten them a hand, and then tighten bolts till the required inhaling moment.
12. Establish a forward axis.
13. Establish a protective plate of the engine and lower the car on the earth.
14. Fill in new engine oil in the engine and connect a wire of the minus plug of the accumulator.