Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. Electric equipment and capital repairs of engines
      3.2.1. Electric equipment of engines
      3.2.2. Capital repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and repair of the engine
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. Cover of a head of cylinders
         3.2.2.5. Yokes and rollers of yokes
         3.2.2.6. Thermostat
         3.2.2.7. The soaking-up collector
         3.2.2.8. Final collector
         3.2.2.9. Turbocompressor
         3.2.2.10. Conditioner
         3.2.2.11. Radiator
         3.2.2.12. The cooling system fan with the drive from the electric motor
         3.2.2.13. Pump of cooling liquid
         3.2.2.14. Head of cylinders
         3.2.2.15. Valves and springs
         3.2.2.16. Pushers
         3.2.2.17. Oil pallet
         3.2.2.18. Oil pump
         3.2.2.19. Epiploon of a forward cover of a gear belt
         3.2.2.20. Chain of the drive of the camshaft and asterisk of the drive
         3.2.2.21. Forward cover of a gear belt
         3.2.2.22. Epiploon of a bent shaft
         3.2.2.23. Gear belt and natyazhitel
         3.2.2.24. Gear belt and mechanism of a tension
         3.2.2.25. Drive of the gas-distributing mechanism petrol engines
         3.2.2.26. Drive of the gas-distributing mechanism diesel engines
         3.2.2.27. Camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Conrod bearings
         3.2.2.31. Assembly of conrod and piston group and installation on the engine
         3.2.2.32. Caps and heater of a case of the engine
         3.2.2.33. Back epiploon of a bent shaft
         3.2.2.34. Bent shaft and radical bearings
         3.2.2.35. Flywheel and gear wreath
   3.3. Diesel engine 2,8 liters
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries




 

Isuzu Trooper>> Engines>> Electric equipment and capital repairs of engines>> Capital repairs of engines>> Cover of a head of cylinders

3.2.2.4. Cover of a head of cylinders

GENERAL INFORMATION

4-CYLINDER SINGLE-SHAFT ENGINES

Cover of a head of cylinders on 4-cylinder single-shaft engines

1 – zolotnik of ventilation of a case

2 – spark plug wire

3 – bolts of a forward cover

4 – bolts of a cover of a head of cylinders

5 – cover of a head of cylinders

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Remove the air filter (on carburetor engines) or an air duct. (on injector engines).
3. Remove a hose of a zolotnik of ventilation of a case.
4. Mark and disconnect wires of spark plugs.
5. Turn off bolts of a forward cover.
6. Disconnect a hose of the vacuum amplifier of brakes and a cable of the drive of a butterfly valve.
7. Turn off bolts of fastening of a cover of a head of cylinders and uncover.
8. If the cover does not give in to removal, then displace it, having knocked on it with the rubber hammer.

Installation

PERFORMANCE ORDER
1. Clear the space for laying of the remains of old consolidation.
2. Establish new laying on a cover. Apply sealant drops like RTV with a diameter of 2-3 mm on the condensed surface.
3. Establish a cover and tighten bolts with m 10 N.' moment.
4. Establish wires of spark plugs, a zolotnik of ventilation of a case, a hose of the vacuum amplifier of brakes and a cable of the drive of a butterfly valve (if acted for expansion of working space).
5. Install the air filter or an air duct.
6. Connect the battery to weight. Start the engine, be convinced of lack of a leak.

V6 ENGINES

Cover of a head of cylinders on 6-cylinder engines

And – the place of putting sealant

1 – nuts

2 – intensifying plate

3 – cover

4 – laying

5 – hairpins

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Remove the air filter.
3. Remove the coil of ignition and an arm (at removal of the right cover) and the valve of ventilation of a case (at removal of the left cover).
4. Mark and get wires of spark plugs from an arm, strengthened on a cover hairpin.
5. Remove a zolotnik of ventilation of a case (at removal of the right cover).
6. Remove a cable of the drive of a butterfly valve and the generator (only at removal of the right cover).
7. Turn off nuts of fastening of a cover, remove safety plates, a cover and laying. If the cover does not give in to removal, then knock on it with the rubber hammer, at the same time do not damage a flange part of a cover.

Installation

PERFORMANCE ORDER
1. Clear the space for laying of the remains of old consolidation.
2. Establish a cover with new laying.
3. Establish intensifying plates and wrap cover nuts. Tighten nuts with m 8 N.' moment.
4. Establish a cable of the drive of a butterfly valve and the generator (only at removal of the right cover).
5. Establish a zolotnik of ventilation of a case (at removal of the right cover).
6. Establish wires of spark plugs in an arm.
7. Install the coil of ignition and an arm (at removal of the right cover) or the valve of ventilation of a case (at removal of the left cover).
8. Install the air filter.
9. Attach the battery with a weight. Start the engine, be convinced of lack of a leak.