Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. Electric equipment and capital repairs of engines
      3.2.1. Electric equipment of engines
      3.2.2. Capital repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and repair of the engine
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. Cover of a head of cylinders
         3.2.2.5. Yokes and rollers of yokes
         3.2.2.6. Thermostat
         3.2.2.7. The soaking-up collector
         3.2.2.8. Final collector
         3.2.2.9. Turbocompressor
         3.2.2.10. Conditioner
         3.2.2.11. Radiator
         3.2.2.12. The cooling system fan with the drive from the electric motor
         3.2.2.13. Pump of cooling liquid
         3.2.2.14. Head of cylinders
         3.2.2.15. Valves and springs
         3.2.2.16. Pushers
         3.2.2.17. Oil pallet
         3.2.2.18. Oil pump
         3.2.2.19. Epiploon of a forward cover of a gear belt
         3.2.2.20. Chain of the drive of the camshaft and asterisk of the drive
         3.2.2.21. Forward cover of a gear belt
         3.2.2.22. Epiploon of a bent shaft
         3.2.2.23. Gear belt and natyazhitel
         3.2.2.24. Gear belt and mechanism of a tension
         3.2.2.25. Drive of the gas-distributing mechanism petrol engines
         3.2.2.26. Drive of the gas-distributing mechanism diesel engines
         3.2.2.27. Camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Conrod bearings
         3.2.2.31. Assembly of conrod and piston group and installation on the engine
         3.2.2.32. Caps and heater of a case of the engine
         3.2.2.33. Back epiploon of a bent shaft
         3.2.2.34. Bent shaft and radical bearings
         3.2.2.35. Flywheel and gear wreath
   3.3. Diesel engine 2,8 liters
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Engines>> Electric equipment and capital repairs of engines>> Capital repairs of engines>> Flywheel and gear wreath

3.2.2.35. Flywheel and gear wreath

GENERAL INFORMATION

Sequence of an inhaling of bolts of a flywheel

1 – the correct installation of a washer – from a bolt

2 – from the engine

3 – the place of drawing the fixing structure of Loctite

On cars with automatic transmission the gear wreath of a flywheel is not subject to replacement. The wreath is removed only on cars from the manual transmission in a workshop of car service.

Removal and installation

PERFORMANCE ORDER
1. Remove transmission (see subsection 6.1.3 and subsection 6.2.5).
2. Turn off six or seven bolts of fastening and remove a flywheel.
3. At strong damages replace a flywheel. Small agnails can be removed with a file.
4. Establish a flywheel. Wrap bolts with the set moment in a cross order.