Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. Electric equipment and capital repairs of engines
      3.2.1. Electric equipment of engines
      3.2.2. Capital repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and repair of the engine
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. Cover of a head of cylinders
         3.2.2.5. Yokes and rollers of yokes
         3.2.2.6. Thermostat
         3.2.2.7. The soaking-up collector
         3.2.2.8. Final collector
         3.2.2.9. Turbocompressor
         3.2.2.10. Conditioner
         3.2.2.11. Radiator
         3.2.2.12. The cooling system fan with the drive from the electric motor
         3.2.2.13. Pump of cooling liquid
         3.2.2.14. Head of cylinders
         3.2.2.15. Valves and springs
         3.2.2.16. Pushers
         3.2.2.17. Oil pallet
         3.2.2.18. Oil pump
         3.2.2.19. Epiploon of a forward cover of a gear belt
         3.2.2.20. Chain of the drive of the camshaft and asterisk of the drive
         3.2.2.21. Forward cover of a gear belt
         3.2.2.22. Epiploon of a bent shaft
         3.2.2.23. Gear belt and natyazhitel
         3.2.2.24. Gear belt and mechanism of a tension
         3.2.2.25. Drive of the gas-distributing mechanism petrol engines
         3.2.2.26. Drive of the gas-distributing mechanism diesel engines
         3.2.2.27. Camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Conrod bearings
         3.2.2.31. Assembly of conrod and piston group and installation on the engine
         3.2.2.32. Caps and heater of a case of the engine
         3.2.2.33. Back epiploon of a bent shaft
         3.2.2.34. Bent shaft and radical bearings
         3.2.2.35. Flywheel and gear wreath
   3.3. Diesel engine 2,8 liters
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Engines>> Electric equipment and capital repairs of engines>> Capital repairs of engines>> Drive of the gas-distributing mechanism petrol engines

3.2.2.25. Drive of the gas-distributing mechanism of petrol engines

ENGINES 4ZD1 AND 4ZE1

Camshaft asterisk

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Take off a gear belt.
3. Turn off a bolt and remove a camshaft asterisk. To facilitate removal of an asterisk carefully knock on it with the hammer and get moving forward.
4. Remove a camshaft epiploon (which is subject to replacement).

Installation

PERFORMANCE ORDER
1. Combine tags on an asterisk of the camshaft and on a back cover of a gear belt, establish an asterisk. Put on a belt.
2. Bring a roller of a natyazhitel to a belt that the roller rested against a belt under the influence of a spring.
3. Turn a bent shaft on 2 whole revolutions in a direction opposite to normal rotation and be convinced that adjusting tags coincided again.
4. Release a bolt of a roller of a natyazhitel that the belt stretched under the influence of a spring. Tighten a roller bolt with m 22 N.' moment.
5. Establish covers of a gear belt and a pulley of a bent shaft.
6. Connect the battery to weight, start the engine and be convinced of lack of a leak.

Leading asterisk of a bent shaft

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Take off a gear belt.
3. Turn off a bolt and by means of a stripper remove an asterisk of a bent shaft.
4. Remove an epiploon of a bent shaft (which is subject to replacement).

Installation

PERFORMANCE ORDER
1. Combine tags on the leading asterisk of a bent shaft and on a cover of the holder of an epiploon.
2. Check combination of adjusting tags of the camshaft and put on a belt.
3. Bring a roller of a natyazhitel to a belt that the roller rested against a belt under the influence of a spring.
4. Turn a bent shaft on 2 whole revolutions in a direction opposite to normal rotation and be convinced that adjusting tags coincided again.
5. Release a bolt of a roller of a natyazhitel that the belt stretched under the influence of a spring. Tighten a roller bolt with m 22 N.' moment.
6. Establish covers of a gear belt and a pulley of a bent shaft.
7. Other procedures are performed upside-down.