Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. Electric equipment and capital repairs of engines
      3.2.1. Electric equipment of engines
      3.2.2. Capital repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and repair of the engine
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. Cover of a head of cylinders
         3.2.2.5. Yokes and rollers of yokes
         3.2.2.6. Thermostat
         3.2.2.7. The soaking-up collector
         3.2.2.8. Final collector
         3.2.2.9. Turbocompressor
         3.2.2.10. Conditioner
         3.2.2.11. Radiator
         3.2.2.12. The cooling system fan with the drive from the electric motor
         3.2.2.13. Pump of cooling liquid
         3.2.2.14. Head of cylinders
         3.2.2.15. Valves and springs
         3.2.2.16. Pushers
         3.2.2.17. Oil pallet
         3.2.2.18. Oil pump
         3.2.2.19. Epiploon of a forward cover of a gear belt
         3.2.2.20. Chain of the drive of the camshaft and asterisk of the drive
         3.2.2.21. Forward cover of a gear belt
         3.2.2.22. Epiploon of a bent shaft
         3.2.2.23. Gear belt and natyazhitel
         3.2.2.24. Gear belt and mechanism of a tension
         3.2.2.25. Drive of the gas-distributing mechanism petrol engines
         3.2.2.26. Drive of the gas-distributing mechanism diesel engines
         3.2.2.27. Camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Conrod bearings
         3.2.2.31. Assembly of conrod and piston group and installation on the engine
         3.2.2.32. Caps and heater of a case of the engine
         3.2.2.33. Back epiploon of a bent shaft
         3.2.2.34. Bent shaft and radical bearings
         3.2.2.35. Flywheel and gear wreath
   3.3. Diesel engine 2,8 liters
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Engines>> Electric equipment and capital repairs of engines>> Capital repairs of engines>> Epiploon of a bent shaft

3.2.2.22. Epiploon of a bent shaft

PETROL 4-CYLINDER ENGINES

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight. Remove a pulley of a bent shaft.
2. Uncover top and lower a gear belt.
3. Turn a bent shaft so that tags on an asterisk of the camshaft and on a back cover of a gear belt were combined, and the spline on a sock of a bent shaft was established opposite to a cover of the holder of an epiploon. When the specified tags are combined, the piston of the 4th cylinder is in compression step VMT.
4. Weaken a tension of a gear belt, having released a bolt of a natyazhitel, take off a belt from an asterisk of a bent shaft.
5. Turn off a bolt of an asterisk of a bent shaft, remove an asterisk, a spline and a maslootrazhatelny guard.
6. Carefully to a vypressuyta an epiploon from the holder, having hooked it the small screw-driver.

Installation

PERFORMANCE ORDER
1. Oil a new epiploon for the engine and press it in the holder easy blows to a mandrel.
2. Establish a guard, a spline, an asterisk of a bent shaft and wrap a bolt.
3. Combine an adjusting tag on an asterisk of a bent shaft, put on a gear belt.
4. Release a spring and pull a gear belt.
5. Turn a bent shaft on 2 whole revolutions in a direction opposite to normal rotation and again combine adjusting tags.
6. Weaken a bolt of a natyazhitel that the roller rested against a belt, and the correct tension was provided.
7. Establish covers of a gear belt and a pulley of a bent shaft.
8. Other procedures are performed upside-down.

DIESEL ENGINES

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight, merge cooling liquid.
2. Take off a gear belt.
3. Turn off a bolt of a pulley of a bent shaft. It can be necessary for an otvorachivaniye of a bolt to stop a flywheel to exclude a provorachivaniye of a bent shaft for what it is necessary to remove a starter, or a flywheel cover.
4. Press an asterisk from a bent shaft.
5. Turn off bolts of fastening of the holder of an epiploon to a back cover of a gear belt, remove the holder.
6. Press an epiploon, having hooked it the small screw-driver.

Installation

PERFORMANCE ORDER
1. Oil working edges of a new epiploon for the engine, press an epiploon into place.
2. Establish the holder of an epiploon.
3. Establish the leading asterisk on a bent shaft.
4. Establish a gear belt.
5. Fill in cooling liquid, establish ignition, start the engine and be convinced of lack of a leak.