Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. Electric equipment and capital repairs of engines
      3.2.1. Electric equipment of engines
      3.2.2. Capital repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and repair of the engine
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. Cover of a head of cylinders
         3.2.2.5. Yokes and rollers of yokes
         3.2.2.6. Thermostat
         3.2.2.7. The soaking-up collector
         3.2.2.8. Final collector
         3.2.2.9. Turbocompressor
         3.2.2.10. Conditioner
         3.2.2.11. Radiator
         3.2.2.12. The cooling system fan with the drive from the electric motor
         3.2.2.13. Pump of cooling liquid
         3.2.2.14. Head of cylinders
         3.2.2.15. Valves and springs
         3.2.2.16. Pushers
         3.2.2.17. Oil pallet
         3.2.2.18. Oil pump
         3.2.2.19. Epiploon of a forward cover of a gear belt
         3.2.2.20. Chain of the drive of the camshaft and asterisk of the drive
         3.2.2.21. Forward cover of a gear belt
         3.2.2.22. Epiploon of a bent shaft
         3.2.2.23. Gear belt and natyazhitel
         3.2.2.24. Gear belt and mechanism of a tension
         3.2.2.25. Drive of the gas-distributing mechanism petrol engines
         3.2.2.26. Drive of the gas-distributing mechanism diesel engines
         3.2.2.27. Camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Conrod bearings
         3.2.2.31. Assembly of conrod and piston group and installation on the engine
         3.2.2.32. Caps and heater of a case of the engine
         3.2.2.33. Back epiploon of a bent shaft
         3.2.2.34. Bent shaft and radical bearings
         3.2.2.35. Flywheel and gear wreath
   3.3. Diesel engine 2,8 liters
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Engines>> Electric equipment and capital repairs of engines>> Capital repairs of engines>> Chain of the drive of the camshaft and asterisk of the drive

3.2.2.20. Chain of the drive of the camshaft and asterisk of the drive

GENERAL INFORMATION

V6 ENGINE

Adjusting tags of the chain drive of the camshaft on V6 engines

And – the piston of the 1st cylinder in compression step VMT

In – the piston of the 4th cylinder in compression step VMT

1 – bolt

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Install the piston of the 1st cylinder in compression step VMT.
3. Remove a forward cover.
4. Check a condition of asterisks, existence of wear signs for them and the broken teeths.
5. Check a condition of a chain. If it is possible to delay a chain from an uspokoitel more than on 9,5 mm, then the chain is worn-out and is subject to replacement.
6. Turn off bolts of fastening of an asterisk to the camshaft, remove an asterisk and a chain. If necessary bring down an asterisk from the camshaft easy blows of the hammer.
7. Press an asterisk from a bent shaft.

Installation

PERFORMANCE ORDER
1. Napressuyte an asterisk on a bent shaft, having paid attention to that the adjusting tag was turned up.
2. Grease a persistent surface of an asterisk of the camshaft with molybdenic Molykote lubricant or equivalent, dress a chain on an asterisk.
3. Holding an asterisk in vertical position, combine tags on asterisks of a bent shaft and the camshaft.
4. Combine a pin on the camshaft with an opening in an asterisk, tighten bolts with m 23 N.' moment.
5. Oil a chain for the engine.
6. Establish a forward cover and a pulley of a bent shaft.
7. Connect the battery to weight.
8. Start the engine, check installation of ignition, if necessary adjust.