Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
   3.1. Specifications of the engine and adjusting works
   3.2. Electric equipment and capital repairs of engines
      3.2.1. Electric equipment of engines
      3.2.2. Capital repairs of engines
         3.2.2.1. Technical characteristics
         3.2.2.2. Instructions on service and repair of the engine
         3.2.2.3. Dismantle and installation of the power unit
         3.2.2.4. Cover of a head of cylinders
         3.2.2.5. Yokes and rollers of yokes
         3.2.2.6. Thermostat
         3.2.2.7. The soaking-up collector
         3.2.2.8. Final collector
         3.2.2.9. Turbocompressor
         3.2.2.10. Conditioner
         3.2.2.11. Radiator
         3.2.2.12. The cooling system fan with the drive from the electric motor
         3.2.2.13. Pump of cooling liquid
         3.2.2.14. Head of cylinders
         3.2.2.15. Valves and springs
            3.2.2.15.1. Check of springs
            3.2.2.15.2. The directing plugs of valves
            3.2.2.15.3. Saddles of valves
            3.2.2.15.4. Grinding in of valves
         3.2.2.16. Pushers
         3.2.2.17. Oil pallet
         3.2.2.18. Oil pump
         3.2.2.19. Epiploon of a forward cover of a gear belt
         3.2.2.20. Chain of the drive of the camshaft and asterisk of the drive
         3.2.2.21. Forward cover of a gear belt
         3.2.2.22. Epiploon of a bent shaft
         3.2.2.23. Gear belt and natyazhitel
         3.2.2.24. Gear belt and mechanism of a tension
         3.2.2.25. Drive of the gas-distributing mechanism petrol engines
         3.2.2.26. Drive of the gas-distributing mechanism diesel engines
         3.2.2.27. Camshaft
         3.2.2.28. Camshaft bearings
         3.2.2.29. Pistons and rods
         3.2.2.30. Conrod bearings
         3.2.2.31. Assembly of conrod and piston group and installation on the engine
         3.2.2.32. Caps and heater of a case of the engine
         3.2.2.33. Back epiploon of a bent shaft
         3.2.2.34. Bent shaft and radical bearings
         3.2.2.35. Flywheel and gear wreath
   3.3. Diesel engine 2,8 liters
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Engines>> Electric equipment and capital repairs of engines>> Capital repairs of engines>> Valves and springs>> Check of springs

3.2.2.15.1. Check of springs

GENERAL INFORMATION

Check of pressure of a spring of the valve by means of testers

Check of length of a spring in a free state and its cross deformation

1 – deformation size

2 – spring

Establish a spring on a plain surface near a square and check height and a deviation from a vertical for what the spring should be turned concerning a square. If at turn of a spring it is found out that height changes more than on 1,5 mm, or the deviation from a vertical exceeds 1,5 mm, then replace a spring. It is necessary to measure also dispersion of pressure of a spring in a condition of the closed and open valve (height is in a condition of the closed valve by subtraction from height of the open valve of size of its rise). For springs of engines with a volume up to 3,0 l the dispersion (±) of 0,4 kgfs, and for engines with large volume – to (±) 2,0 kgfs is allowed.