Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
   2.1. Data on identification of the car
   2.2. General data of engines
   2.3. THAT the Trooper/Bighorn cars with the diesel engine
   2.4. Instructions on leaving
      2.4.1. Air filter
      2.4.2. Fuel filter (petrol engines)
      2.4.3. Fuel filter (diesel engines)
      2.4.4. Draining of the water which collected in fuel system of the diesel engine
      2.4.5. Compulsory system of ventilation of a case (PCV system)
      2.4.6. A tank for catching of vapors of gasoline
      2.4.7. Features of check of system of catching of vapors
      2.4.8. Rechargeable battery
      2.4.9. Drive belts
      2.4.10. Cooling system
      2.4.11. Air conditioning system
      2.4.12. Screen wiper
      2.4.13. The recommended brands of fuel and oil
      2.4.14. Care of the manual transmission or automatic transmission
      2.4.15. Check of level of oil or liquid
      2.4.16. Oil replacement
      2.4.17. Case of the transfer case
      2.4.18. Reducer of the back bridge
      2.4.19. Cooling liquid
      2.4.20. Main brake cylinder
      2.4.21. Main cylinder of a hydraulic actuator of coupling
      2.4.22. Nutritious tank of the power steering
      2.4.23. Reducer of the steering mechanism
      2.4.24. Lubricant of a running gear
      2.4.25. Body lubricant
      2.4.26. Lubricant of the mechanism of the emergency brake
      2.4.27. Lubricant of draft of the drive of a butterfly valve
      2.4.28. Gear shifting lever lubricant
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
12. Electrical circuitries





Isuzu Trooper>> Maintenance>> Instructions on leaving>> Screen wiper

2.4.12. Screen wiper

GENERAL INFORMATION

For extension of service life of a screen wiper it is necessary to delete from a pollution windshield, caused by hit of leaves, tar from a paving, etc. which result in the increased wear of rubber brushes. Rubber scrapers are replaced in process of their wear, as a rule, annually. Indicate bad removal of water, a non-uniform prileganiye or the raised gnash the need of their replacement during the work of a screen wiper.

It is expedient to replace brushes in couple.

Replacement of brushes

TRICO:
1 – brush holder lever
2 – rubber scraper of a brush
3 – squeeze an ogranitel on each side
4 – lever sponges
5 – unclench
6 – wider metal substrate of the brush holder
7 – limiters
8 – lever bracket
9 – edging of a metal substrate
10 – hold against twisting
11 – полосковя metal substrate
12 – hook the screw-driver
ANCO:
13 – sponges
14 – hinge
POLYCARBONAT:
15 – the brush is brought out of the lock
16 – the brush is recorded
TRIDON:
17 – plastic substrate
18 – groove
19 – bracket
20 – brush scraper
21 – press
22 – tighten and turn
23 – teeth of clamps
24 – at edges of brushes like TRIDON the numbers specifying their length (16 and 16,5) are cast, new brushes or scrapers have to be just the same length
25 – firm surface

PERFORMANCE ORDER
1. For removal of a rubber brush it is necessary to insert the screw-driver under a spring bracket and to turn.
2. Displace a brush and get it from limiters.
3. To insert a new brush it is necessary to bring it to gearing with limiters in the brush holder, to combine a groove in a scraper with a ledge on the brush holder and to record a brush.