Isuzu Trooper - Isuzu Trooper
1. Maintenance instruction
2. Maintenance
3. Engines
4. System of decrease in toxicity
5. Fuel system
6. Transmission and running gear
7. Suspension bracket and steering
8. Brake system
9. Body
10. Body electric equipment
11. Diagnostics of malfunctions
   11.1. Main malfunctions of coupling
   11.2. Main malfunctions of the manual transmission
   11.3. Main malfunctions of the driveshaft
   11.4. Main malfunctions of steering and suspension bracket
   11.5. Main malfunctions of the steering mechanism
   11.6. The main malfunctions of the steering mechanism with the hydraulic booster
   11.7. Main malfunctions of brakes
   11.8. Characteristic malfunctions of the engine and ways of elimination
   11.9. Characteristic malfunctions in the engine cooling system
   11:10. Characteristic malfunctions of a belt of the drive with a corrugated profile
   11:11. Characteristic malfunctions of a power supply system (carburetor engines)
   11:12. Characteristic malfunctions of signals of turn and emergency stop 11_13.htm
12. Electrical circuitries





Isuzu Trooper>> Diagnostics of malfunctions>> Main malfunctions of steering and suspension bracket

11.4. Main malfunctions of steering and suspension bracket

GENERAL INFORMATION

REASON
WAY OF ELIMINATION
Hard rotation of a steering wheel
Low or unequal pressure in tires
To restore pressure.
Weakening of a belt of the drive of the pump of the hydraulic booster
To adjust a tension.
Low level of liquid or brand of liquid in a hydraulic actuator does not correspond to recommended
To add liquid or to replace.
Violation of angles of installation of wheels
To check and adjust the angles of installation of wheels.
The pump of the hydraulic booster is faulty
To check the pump.
Curvature or lack of lubricant in details of a forward suspension bracket
To grease and replace the damaged details.
The raised side play of a steering wheel
Violation of adjustment of bearings of forward wheels
To adjust.
Wear of tips of steering drafts
To replace worn-out details.
Shock-absorbers are faulty
To replace shock-absorbers.
Wear of spherical hinges of levers of a suspension bracket
To replace spherical hinges.
The car takes away aside
Pressure in tires differs from norm
To restore pressure.
Violation of angles of installation of wheels
To check and adjust the angles of installation of wheels.
Violation of adjustment of bearings of forward wheels
To adjust.
Curvature of details of a forward suspension bracket
To replace the damaged details.
Shock-absorbers are faulty
To replace shock-absorbers.
Vibrations of forward wheels which are felt on a wheel
Pressure in tires does not correspond to normal
To restore pressure.
Violation of balancing of wheels
To balance wheels.
Violation of adjustment of bearings of forward wheels
To adjust.
Violation of disorder and convergence of wheels
To check and adjust all angles of installation of wheels.
Deformation of details of a forward suspension bracket
To replace the damaged details.
Uneven wear of tires
Pressure in tires differs from norm
To restore pressure.
Violation of angles of installation of wheels
To check and adjust the angles of installation of wheels.
Violation of balancing of wheels
To balance wheels.
The wheel is not locked
Breakage of a spring
To replace a spring.
The complicated turn of a key in the ignition lock
The lock cylinder is faulty
To replace the cylinder.
Contact part of the lock is faulty
To replace.
Breakage or deformation of a persistent spring of a lath
To replace a spring.
Agnails on lock drive details (a lath, the coupling, the sector, the case)
To remove agnails.
The sector shaft is bent
To replace a shaft.
The locking core of the lock is faulty
To replace a core.
Deformation of a rod
To replace a rod.
Deformation of an arm of the lock of ignition
To correct or replace.
Deformation of a groove in a locking core (an adjustable steering column)
To replace a core.
The key jams in situation "START"
Deformation of the roller of the lock
To straighten or replace.
Deformation of an arm of the lock of ignition
To correct or replace.
The key cannot be taken from situation "off-lock"
To adjust the ignition lock.
The lock cylinder is faulty
To replace the cylinder.
The lock gets without cave-in of a lock ring
The cylinder is faulty
To replace.
Agnails in a flute of a lock ring in the case or on a lock ring
To remove agnails.
Big effort when translating a key from situation "off" in situation "off-lock" and vice versa
Deformation of a locking core
To replace a core.
Agnails on a tail part of a lock (an automatic column)
To remove agnails.
Draft of the lever of change of an inclination of a column is not adjusted
To adjust.
Noise of a steering column
Click at transfer of a key to situation "off-lock" then the wheel will begin to rotate
It is allowed (the clamp comes back to a starting position).
Weakening of the pulling together bolts
To tighten bolts.
In bearings there is no lubricant
To grease bearings.
Breakage or wear of the bearing of the top shaft
To replace the bearing assembled.
Breakage or wear of the bearing of the lower shaft
To replace the bearing. To check a condition of a shaft, at detection of zadir to replace.
Violation of the correct provision of a column
To expose a column.
Breakage of the coupling
To replace the coupling.
Breakage of the lower hinge
To repair the hinge or to replace. To correct the coupling.
Leaky landing of a lock ring of a steering shaft
To replace a ring. To check reliability of landing of a ring.
Weakening of a casing of a column. It is found at rotation of a wheel
To expose a casing and to tighten screws.
The complicated rotation of a steering shaft
Wrong provision of a steering column
To expose a column.
Defect in bearings of the top or lower shaft
To replace bearings.
Hard rotation of the cardan hinge
To repair or replace.
Agnails on the plastic hinge of the sliding shlitsevy connection (an adjustable column) To replace the coupling of the sliding shlitsevy connection.
Side play of a steering column
Weakening of bolts of an arm of a steering column
To tighten bolts.
Breakage of welding of the nuts welded on the wheel shaft case
To replace the case.
Deformation of lock plates of an arm of the case of a steering column
To replace an arm.
Weakening of bolts of fastening of an arm to the case of a steering shaft
To tighten bolts a dynamometer key.
Weakening of the blocking blocks in the case (in an adjustable steering column)
To replace blocks.
Weakening of axes of hinges (in an adjustable steering column)
To replace axes of hinges and a support.
Weakening of axes of hinges of the blocking blocks (in an adjustable steering column)
To replace axes of hinges and the case.
Weakening of bolts of fastening of a support (in an adjustable steering column)
To tighten bolts.
Weakening of fastening of the case (only for adjustable columns)
The raised gap between axes and openings in a support or the case
To replace axes and a support.
Weakening of bolts of fastening of a support to the case
To tighten bolts.
Weakening of a steering wheel in any situation (only for adjustable columns)
The raised gap between axes and the blocking blocks
To replace blocks and axes.
The steering wheel is not locked at any inclination (only for adjustable columns)
Holding strap of blocks to an axis
To replace blocks and axes.
On flutes of blocks there are teases or pollution of flutes
To clear or replace blocks.
Breakage or loss of elasticity of springs of blocks
To replace springs.
Noise at change of an inclination of a steering column (only for adjustable columns)
Wear of the top buffer
To replace the buffer.
The increased friction of a spring in the case
To grease with graphite lubricant.
Big effort when changing an inclination of a column (only for automatic and adjustable columns)
Violation of provision of a column
To expose a column.
Distortion of the lower bearing
To sort and expose the bearing.
Lack of lubricant in an epiploon or the lower bearing
To grease.
Abnormal operation of the mechanism of change of an inclination of a column (only for automatic and adjustable columns)
Vents of tubular connection are cut off
To replace tubular connection.
Draft of the lever of change of an inclination of a column is not adjusted
To adjust.
Weakening of the lower lever
To replace tubular connection.